CORROGLASS
Corroglass AR4
Product reference: 2/36
Product title: Corroglass AR4
Valid from: 27th November 1997
Last reviewed: 31 May 2019
Type: A two-pack cold cured brominated vinyl ester/acrylic co-polymer enhanced
with flake glass.
Suggested use
Corroglass AR4 has been specially formulated to offer the
best resistance to base environments, e.g. Sodium Hydroxide
and Sodium Hypochlorite, the resin and cure system having
been modified to impart the optimum resistance to these
environments.
best resistance to base environments, e.g. Sodium Hydroxide
and Sodium Hypochlorite, the resin and cure system having
been modified to impart the optimum resistance to these
environments.
Health & safety
Before commencing work, read the product Health &
Safety data sheet. Corroglass AR4 should only be used by
adequately trained personnel.
Safety data sheet. Corroglass AR4 should only be used by
adequately trained personnel.
Surface preparation
Metals: Grit blast to SPCC-SP10 (ISO standard 8501-1
Sa 2½ near 3) standard or equivalent. (For full details
refer to Corrocoat Surface Specification SP1).
Concrete: Grit blast to remove surface laitance. See
Corrocoat Surface Specification SP5.
Sa 2½ near 3) standard or equivalent. (For full details
refer to Corrocoat Surface Specification SP1).
Concrete: Grit blast to remove surface laitance. See
Corrocoat Surface Specification SP5.
Hardener type
Catalyst type – Organic Peroxide.
Pot life
Approximately 55-65 minutes at 68° F (20°C) (may vary
dependent upon temperature and age of product).
dependent upon temperature and age of product).
Pot life
Approximately 55-65 minutes at 68° F (20°C) (may vary
dependent upon temperature and age of product).
dependent upon temperature and age of product).
Hardness
45 Barcol.
Elongation at break
0.3%
Dielectric strength
18 – 25 x 10³ V/mm
Tensile strength
3845 PSI (26.5 N mm 2)
Overcoating
May take place as soon as the previous coat has gelled
and while still tacky. Maximum overcoating time 72 hours
at 68°F (20°C).
Once the maximum overcoating time has been reached, the
adhesion values attained by any subsequent coat will reduce
dramatically. It is important to observe maximum overcoating
times and note these will vary with climatic conditions. Any
further application of coating at this juncture should be
treated as a repair, with the surface flashed over to provide
a physical key. Styrene cannot be used to reactivate the
surface and may in some cases impair adhesion.
and while still tacky. Maximum overcoating time 72 hours
at 68°F (20°C).
Once the maximum overcoating time has been reached, the
adhesion values attained by any subsequent coat will reduce
dramatically. It is important to observe maximum overcoating
times and note these will vary with climatic conditions. Any
further application of coating at this juncture should be
treated as a repair, with the surface flashed over to provide
a physical key. Styrene cannot be used to reactivate the
surface and may in some cases impair adhesion.
Cleaning solvent
Methyl Ethyl Ketone, Acetone and Methyl Iso Butyl Ketone
prior to gelation.
prior to gelation.
Mixing ratio / mixing
98:2 Base: Hardener
Application equipment
For spray application use a Graco King 45:1, or similar,
airless pump, 10mm diameter (3/8”) nylon spray line. Large
bore mastic type gun with 30 to 60 thou reversible or titan
adjustable tip. As a guide, a typical tip size would be 31-35
thou with a 60° fan pattern. The size of tip and fan pattern will
vary dependent upon the nature of the work.
May be hand applied using a brush, roller or trowel.
airless pump, 10mm diameter (3/8”) nylon spray line. Large
bore mastic type gun with 30 to 60 thou reversible or titan
adjustable tip. As a guide, a typical tip size would be 31-35
thou with a 60° fan pattern. The size of tip and fan pattern will
vary dependent upon the nature of the work.
May be hand applied using a brush, roller or trowel.
Application
Corroglass AR4 is normally applied at wet films between 20-
40 mils (500-1000 microns).
40 mils (500-1000 microns).
Thinners
The performance of Corroglass AR4 may be significantly
affected by the addition of styrene. DO NOT ADD SOLVENT
or THINNERS.
affected by the addition of styrene. DO NOT ADD SOLVENT
or THINNERS.
Storage life
6 Months if stored at temperatures below 68°F (20°C)
and away from direct heat and sunlight.
and away from direct heat and sunlight.
Color availability
Unpigmented or off-white.
Recommended DFT
20-118 mils (500-3000 Microns) dependent upon service
conditions.
conditions.
Theoretical spreading rate
54 sf per gallon at 29 mils (1.33m²/Litre 750 microns).
Tensile strength
3845 PSI (26.5 N mm 2)
Temperature limits
Dependent upon environment.
179°F (82°C) Immersed
179°F (82°C) Immersed
Curing time
Tack free after 24 hours at 68°F (20°C). Full cure after 4
days. For best results and in most environments, a post
cure of 4-6 hours at 140-176°F (60-80°C) is recommended
prior to service. Refer to Corrocoat Technical Services for
furtherdetails.
days. For best results and in most environments, a post
cure of 4-6 hours at 140-176°F (60-80°C) is recommended
prior to service. Refer to Corrocoat Technical Services for
furtherdetails.
Volume solids
This material contains volatile liquid convertible to
solids. Volume solids obtained will vary dependent upon
polymerization conditions. Nominally 99% of the contents are
convertible to solid.
solids. Volume solids obtained will vary dependent upon
polymerization conditions. Nominally 99% of the contents are
convertible to solid.
Practical spreading rate
43 sf per gallon at 30 mils dft (1.06m²/Litre at 750 microns).
Note: This information is given in good faith but may increase
dependent upon environment conditions, thegeometry
and nature of work undertaken and the skill and care of
application. Corrocoat accepts no responsibility for any
deviation from these values.
Note: This information is given in good faith but may increase
dependent upon environment conditions, thegeometry
and nature of work undertaken and the skill and care of
application. Corrocoat accepts no responsibility for any
deviation from these values.